Best USB Hub for Sim Racing

Disclosure: This post may contain affiliate links. As an Amazon Associate I earn from qualifying purchases. Buying through these links helps support our website at no additional cost to you.

A Direct Drive base has its own power brick. USB carries HID data, not torque. The wheel still wants a rear motherboard port. For the pedals, shifter, and button box, the hub is the Sabrent HB-BU10.

Our Top Picks at a Glance

Reviewed August 2026 · Matched to PC sim rigs (wheel on the motherboard)

01 🏆 Best Overall Sabrent HB-BU10
★★★★★ 4.7 / 5.0 · 2026 pick

10 USB 3.0 data ports, each with a power switch, and a 60W brick. Reset a stuck shifter without crawling behind the PC.

Check Price at Amazon Read full review ↓
02 💎 Best Value Anker A7515 10-Port 60W
★★★★☆ 4.6 / 5.0 · 2026 pick

Same 60W class, 7 data ports plus 3 charge-only. Buy it when you do not need per-port switches. Do not plug a wheel into PowerIQ.

Check Price at Amazon Read full review ↓
03 💰 Budget Pick TP-Link UH700
★★★★☆ 4.4 / 5.0 · 2026 pick

7 powered USB 3.0 ports, 12V/2.5A adapter, 1 m host cable. Right for a G29/T300 plus a shifter. No per-port switches.

Check Price at Amazon Read full review ↓

Disclosure: This page contains affiliate links. As an Amazon Associate affiliate, we earn a small commission from qualifying purchases at no extra cost to you.

Who should buy what

  • Most PC rigs: Sabrent HB-BU10 — wheel on a rear motherboard USB; pedals, shifter, handbrake, and button box on the switched hub. 60W brick in the wall.
  • Same 60W, no switches: Anker A7515 — 7 data ports. Charge a phone on PowerIQ. Keep HID off those three charge-only sockets.
  • Entry wheel + one extra: TP-Link UH700 — 7 ports and a 1 m cable. Skip it once the desk is full of bus-powered RGB boxes.
  • Skip: unpowered travel hubs, putting the wheelbase or a VR headset on the hub, daisy-chaining hubs, and 5V/3A–4A “powered” bricks that are phone chargers.

Comparison Table

ProductBest forData portsPSUPer-port switchesPriceBuy
Sabrent HB-BU10Default rig extras10 USB 3.012V/5A (60W)Yes~$45–$50Check
Anker A751560W, no switches7 data + 3 charge12V/5A (60W)No~$40–$55Check
TP-Link UH700G29 / T300 extras7 USB 3.012V/2.5A (~30W)No~$20–$30Check
ST7300USBME80/20 bolt-on7 USB 3.0Terminal block (adapter often extra)No~$110–$130Check
4-port unpoweredSkip (bus power)4NoneSometimes~$10–$15Check

How We Picked These Hubs

  • The devices: Pedals, shifters, handbrakes, and button boxes are USB HID. They need stable 5V and a polling slot, not 5 Gbps. A Direct Drive motor runs from its own mains brick — USB is not feeding 15–25 Nm. Fanatec’s USB FAQ is blunt: skip long cables and hubs for the Fanatec device; use the stock cable into the PC or console. This page is for the pile of extras once that base already has a rear motherboard port. Load-cell pedals with their own USB, a sequential shifter, and a SimHub dash are the usual passengers.
  • The hub: Powered, with the adapter in the wall. One motherboard port is ~4.5–9 W of bus power; a cluster of HID plus RGB or an Arduino motion box exceeds that and drops devices. The Sabrent HB-BU10 is 10 data ports, individual switches, and a 12V/5A (60W) supply. The Anker A7515 is the same watt class with 7 data ports and 3 PowerIQ charge-only sockets — Anker’s own listing warns those charge ports are not for data, and that some 2.4 GHz wireless and MIDI devices misbehave on USB 3. The UH700 is 7 ports on a 12V/2.5A brick and a 1 m cable. Skip 5V/3A–4A “powered” hubs; 15–20 W is a phone charger wearing a hub shell. Metal industrial boxes help with mounting and ESD. They are not a Faraday cage that “fixes” a DD motor.
  • The PC side: Rear motherboard USB for the hub host cable, not a front-panel header. No daisy-chaining hubs. Windows: turn off USB selective suspend on the controllers you actually use. If a device enumerates badly on a blue USB 3 port, try a USB 2 motherboard port — HID does not need SuperSpeed. VR headsets and capture cards stay on their own motherboard ports. These US bricks are the North American plugs; UK/EU listings need the local adapter, not a travel dongle on a 60W wall wart.

Best USB Hub for Sim Racing: Detailed Reviews

🏆 Best Overall

Sabrent HB-BU10 View on Amazon

Best For: Pedals, shifter, button box on a PC rig
Key Feature: 10 switched data ports + 60W
Rating: 4.7 / 5.0 ★★★★★
Ports10 × USB 3.0 Type-A (all data)
PowerIncluded 12V/5A (60W) adapter
SwitchesPer port, with LED
Host cable~2 ft USB 3.0 (often needs an extension on a wide 80/20)
HousingCompact desktop slab, not a DIN-rail industrial box

Why it fits a sim rig. The useful feature is not 5 Gbps. It is being able to power-cycle one port when Windows loses a Fanatec ClubSport shifter or a Moza handbrake, without unplugging the wheel. Ten data ports is enough for pedals, shifter, handbrake, button box, a USB dash, and a spare. 60W is for that cluster and a phone, not for the Direct Drive motor — that motor never came through USB. The previous version of this page called the shell “industrial aluminum EMI shielding.” Sabrent lists a compact mirrored slab and a 60W adapter. Buy it for the switches and the brick. Mount it near the PC so the short host cable stays short; extend the device cables, not a cheap SuperSpeed run across the cockpit.

Skip this if you only have a wheel and pedals on one USB from the base — you do not need ten ports. Skip it if the brand has to be Anker and that 60W hub is cheaper. Also skip plugging the wheelbase in here when the maker says to use the motherboard.

  • Per-port switches reset a stuck HID device
  • 60W wall brick, not a 5V phone adapter
  • Ten data ports, not seven plus charge-only
  • 2 ft host cable is short on a wide rig
  • Desktop footprint, no 80/20 ears
💎 Best Value

Anker A7515 10-Port 60W View on Amazon

Best For: Same watt class without switches
Key Feature: 7 data + 3 PowerIQ charge-only
Rating: 4.6 / 5.0 ★★★★☆
Ports7 × USB 3.0 data + 3 × PowerIQ charge (no data)
Power12V/5A (60W)
Host cable~2.6 ft
Warranty (Anker)18 months

Why it fits some desks. Value is the 60W supply without paying for ten switches you will not use. Seven data ports cover pedals, shifter, handbrake, and a button box. The three PowerIQ sockets are for a phone or a tablet dash that only needs charge — Anker states they are not data ports and that some 2.4 GHz wireless and MIDI devices are unhappy on this hub. That is a compatibility note, not a reason to buy USB 2 for its own sake. Top-facing ports look tidy on a desk and messy on an 80/20 upright. If street price is within a few dollars of the Sabrent, buy the Sabrent for the switches.

Skip this if you reset devices by toggling a switch every session — that is the HB-BU10. Also skip putting a wheel, a headset dongle, or a VR cable on a charge-only port.

  • 60W class without a Sabrent-sized switch row
  • Charge ports that are actually labelled as charge
  • Slightly longer host cable than the HB-BU10
  • Only seven data ports
  • No per-port power cycle
💰 Budget Pick

TP-Link UH700 View on Amazon

Best For: G29 / T300 plus a shifter
Key Feature: 7 ports, 1 m cable, ~30W brick
Rating: 4.4 / 5.0 ★★★★☆
Ports7 × USB 3.0 Type-A
Power12V/2.5A adapter in the box
Host cable1 m USB 3.0
SwitchesMaster power, not per port

Why it can still fit a rig. Budget here still means a wall adapter, not a bus-powered dongle. Logitech and Thrustmaster entry wheels already put pedals on the base; the hub is for a shifter, a handbrake, and a keyboard. The 1 m host cable is the practical win over the Sabrent’s 2 ft lead. 12V/2.5A is about 30W — enough for HID extras, not a stack of RGB boxes and a USB-powered dash drawing together. No per-port switches: if a device sticks, you unplug it. That is why it is Budget, not Overall.

Skip this if the cockpit already has a DD base, load-cell pedals on their own USB, a sequential, and a button box. That is the 60W Sabrent. Also skip any listing that ships without the 12V brick — an unpowered UH700-shaped slab is a different product.

  • Powered 7-port for entry extras
  • 1 m host cable reaches a floor PC
  • Often half the Sabrent’s street price
  • No per-port reset
  • ~30W, not 60W

If You Need Something Else

These two are not cheaper versions of the Top 3. One is the metal industrial hub this page used to treat as a premium default. One is the unpowered dongle it should have skipped.

👍 80/20 mount

StarTech ST7300USBME View on Amazon

Ports7 × USB 3.0, metal chassis, mounting ears / DIN rail
Protection15 kV air / 8 kV contact ESD; 350 W surge (StarTech spec)
Power7–48V DC terminal block; wall adapter often sold separately
JobBolt to profile, not a $50 desk hub

This is the industrial 7-port with ears, not StarTech’s plastic desktop ST7300USB3B. Buy it when the hub has to screw to 80/20 or live next to a motion controller. Check the listing for a DC adapter — StarTech’s ITB brick is frequently a second SKU. Do not buy it because a DD motor “needs a Faraday cage.” Ground the rig if Fanatec tells you to; that is a wire to the chassis, not a $120 hub.

Skip this if the PC sits under a desk and zip-ties can hold a Sabrent. That is most rigs.

🚫 Skip

Unpowered 4-port USB 3.0 hub View on Amazon

TypeBus-powered travel splitter
PowerShares one motherboard port’s ~4.5–9 W
Rig fitKeyboard on a laptop, not a sim stack

An unpowered hub is how pedals and a shifter fight over bus power and drop mid-stint. The old page also treated 5V/3A–4A Atolla-style bricks as “also great.” 15–20 W is still a phone charger. Individual LEDs do not add watts. Use a wall-powered 30–60W unit, or do not use a hub.

Skip this if the computer is a sim rig. That is the entire point of this row. The same skip applies to putting a VR headset or the wheelbase on any of the Top 3.

Frequently Asked Questions

Does a hub add steering latency?

HID wheels and pedals poll on the order of 1 ms. A powered USB 2/3 hub does not add a frame of delay you can drive around. Packet loss from an unpowered or overloaded hub feels like a disconnect, not like 5 Gbps versus 480 Mbps. Keep the base on the motherboard anyway — that is the Fanatec path, not a latency tweak.

Should the wheelbase go in the hub?

Fanatec says to use the stock cable into the PC or console, not a hub or a long extension, if you are chasing disconnects. Pedals with their own USB, shifters, and button boxes are the hub’s job. Moza and others are less strict; still give the base a rear motherboard port first.

USB 2 or USB 3?

Sim HID does not need SuperSpeed. USB 3 is fine for most people and is what these Amazon hubs are. If a device only enumerates on a black USB 2 motherboard port, use that port for that device. Anker also notes 2.4 GHz wireless and some MIDI gear can fail on USB 3 hubs — move those dongles to a USB 2 port, not off the rig.

Can the VR headset share this hub?

No. Reverb / Quest Link / Pimax-class headsets want their own SuperSpeed motherboard port and often their own power. Put the sim HID on the hub so those ports stay free.

Final Verdict

🏆 Best Overall:
Sabrent HB-BU10 – 10 switched data ports and a 60W brick for rig extras.
Buy Now
💎 Best Value:
Anker A7515 – 60W, 7 data ports, no switches.
Buy Now
💰 Budget Pick:
TP-Link UH700 – 7 powered ports and a 1 m cable for entry extras.
Buy Now

For most sim rigs, buy the Sabrent HB-BU10 and put the wheel on a rear motherboard port. If the Anker A7515 is clearly cheaper and you do not need per-port switches, it is the same 60W class. A G29 or T300 plus a shifter can use the UH700. Do not buy an unpowered travel hub, and do not treat USB as the Direct Drive power feed — the motor has its own brick.

Similar Posts